Effects of Partial Completion on Productivity Index.
ABSTRACT
A new method for analyzing productivity index (PI) on vertical wells is the main objective of this study. Well, performance is often measured in terms of the well’s productivity which is dependent on a number of factors such as the reservoir’s configuration,
the type of completion, petrophysical and fluid properties, formation damage, etc. The effect of partial completion is the main focus of making the productivity index analysis since almost all vertical wells are partially completed due to the reasons of water coning or gas cap issue, etc.
It is also very expensive to fully complete a well especially when the formation thickness is so large. Pressure behavior solutions for both closed boundary and constant pressure boundary have been obtained, taking into consideration the effect of partial completion.
The productivity of a well is usually evaluated on a long-time performance behavior, thus the pseudo-steady state (late time) approach has been employed for the calculation of the productivity index.
Several key factors have been tested on the productivity indexes such as pseudo skin, shape factors, penetration ratio, reservoir drainage area and etc. The effects of these factors have been analyzed on the PI.
Theoretical data were used in carrying out the analysis with results indicating that, productivity index increases with increasing completion interval and vice versa, whiles pressure drop due to skin as a result of restricted entry to fluid flow increases tremendously with decreasing completion interval.
INTRODUCTION
Well, is one of the major concerns in field and provides the means for oil field development . Sometimes, well is measured in terms of productivity index.
In order to arrive at the economic feasibility of drilling a well, petroleum engineers require proven and reliable methods to estimate the expected productivity of that well. Well, productivity is often evaluated using the productivity index, defined as the production rate per unit pressure draw-down.
Petroleum engineers often relate the good productivity evaluation to the long-time performance behavior of a well, that is, the behavior during pseudo-steady-state or/and steady-state flow of a closed system or/and constant pressure system respectively.
The long-term productivity of oil wells is influenced by many factors. Among these factors are petrophysical properties, fluid properties, degree of formation damage and/or stimulation, well geometry, well completions, number of fluid phases, and flow-velocity type (Darcy, non-Darcy) (Yildiz, 2003).
Depending upon the type of wellbore completion configuration, it is possible to have radial, spherical or hemispherical flow near the wellbore. A well with a limited perforated interval (partial completion) could result in spherical flow in the vicinity of the perforations as depicted in fig. 2.1.
A well that only partially penetrates the pay zone could result in hemispherical flow. These conditions could arise where coning of bottom water or gas cap becomes a serious issue (Ahmed, 2005).
Figures 3.1 and 3.2 respectively depict the true picture of radial and spherical flow behavior in a partially completed vertical well. Partial completion is the completion of or flows from less than the entire producing interval.
This situation causes a near-well flow constriction that results in a positive skin effect in a well-test analysis. The net result of partial completion yields extra pressure drop in the near-wellbore region and reduces good productivity.
The present analytical method of evaluating productivity index in vertical wells with partial completion does not account for the effect of pressure drop due to partial completion.
The purpose of this study is to develop an analytical model for evaluating the productivity index (P.I) of vertical wells with partial completion, where the effect of pressure drop due to partial completion is taken into account and compare results with conventional methods.
The partial differential equations were solved for both no-flow boundary and constant pressure boundary systems in Laplace and Fourier Transform domains before inversion to real-time domain.
REFERENCES
Ahmed, T.: “Advanced Reservoir Engineering”, 3rd Edition, 2005. Anadarko Petroleum Corporation.
Babu, D. K. and Odeh, A. S.: “Productivity of a Horizontal Well”. SPE Reservoir Engineering, Vol.4,
No.4, 417- 421, (Nov, 1989).
Bilhartz, H.L. Jr. and Ramey, H. J. Jr: “The Combined Effect of Storage, Skin and Partial Penetration
on Well Test Analysis,” paper SPE 6453 presented at the SPE 52nd Annual Technical Conference
and Exhibition, Denver, Oct, 9-12, 1977.
Brons, F. and Martings, V. E.: “The Effect of Restricted Fluid Entry on Well Productivity”. Journal of
Petroleum Technology, 172-174, (February, 1961).
Carslaw, H. S., and Jaegar, J. C.: “Conduction of Heat in Solids,” Oxford at the Clarendon Press, 1959,
2nd Edition, pp. 185.
Cheng, Y. M.: “Pressure Transient Testing and Productivity Analysis for Horizontal Wells”, PhD
Dissertation, Department of Petroleum Engineering, Texas A& M University, 2003.
Clegg, M. W. and Mills M.: “A study behavior of Partial Penetrated Wells”, July, 1969
Craft, B. C. and Hawkins, M. F.: “Applied petroleum Reservoir Engineering”, 2nd Edition, 1991.
Dake, L. P.: “Fundamentals of reservoir” Elsevier, 1978
Dietz, D. N.: “Determination of Average Reservoir Pressure from Build-Up Surveys”. J. Pet. Tech.,
August, 1965.
Earlougher, R. C., Jr., Ramey, H. J., Jr., Miller, F. G., and Mueller, T. D.: “Pressure Distributions in
Rectangular Reservoir”. Journal of Petroleum Technology, 199-208, (February, 1968).
Economides, M.: Petroleum production systems, 1993
Gringarten, A. C., and Ramey, H. J., Jr.: “The use of Source and Green’s functions in Solving
Unsteady Flow Problems in Reservoirs,” Soc. Pet. Eng. J. (Oct. 1973) 285-296; Trans., AIME, Vol. 255.
GRINGARTEN, A. C. and RAMEY, JR., H.J.: “An Approximate Infinite Conductivity Solution for a
Partially Penetrating Line-Source Well”. SPE Journal, Vol. 15, No.2, pp. 140-148, April 1975.
StudentsandScholarship Team.